• Reloading Guide Online

To view/download, click on the instruction sheet part number or description. Instructions are best viewed and printed with Adobe Acrobat.

So you want to reload, but don’t have the space to do it? Apartment life is sometimes a drag. Space is at a premium and not all of us can afford a spare bedroom just for our gun hobby. Reloading is no different but most people see the “reloading bench” and get turned off by the need of special equipment and a work-space. I have news for you. Reloading can be accomplished on the kitchen table and the components can be stored in a shoebox. I have had success reloading from a small set of tools and for several years I did not have a bench.

Are you ready? Ground Rules: Reloading is not a game for careless people. This guide is for entertainment purposes only. If something isn’t clear, or you need to learn more information, please refer to a professional reloading manual for technical data and instruction. Individuals who use the methods below do so at their own risk and www.thenewrifleman.com and The New Rifleman LLC make no guarantee of success or safety in the outlined reloading methods. Reloading is a safe way to enjoy high quality ammunition at an affordable price, but it is a fast way to a damaged firearm and/or personal injury if you are careless or negligent in using sound methods and techniques to reload your own ammunition.

Equipment List: Calipers (generic) Cordless Drill Chinese Food Take Out Soup Bowl with Lid Shoebox Lee Reloading Manual That’s a lot of gear. Manual for xr 80 honda. Some of it is expensive; however, it is a good investment that will pay you back over the years or decades of use. In my case, I obtained it piece by piece and slowly built up to my current setup. If you have the money for better products all around such as a digital scale vs the Lee beam scale, GO FOR IT. Make your life easier the first time around. So what’s the first step to reloading? Step 1: Wash Your Range Brass The first step is easy.

Give your brass a bath. I use dawn soap and the kitchen sink.

Lots of hot sudsy water. I wash the brass and then dry it over a few days. Set it out in the sun.

We have to get grit off the brass because any grit left behind can get crushed and embedded into your dies. This is not good. Clean brass will equal a happy resizing die. Again, nothing special other than hot soapy water in the sink and a few days to dry.

If you are in a hurry set the brass in the oven at 250 until dry. So after the bath, what’s next?

Reloading Guide Online

Step 2: Resizing, Case Trimming, Case Prep Each time you fire your gun, the brass case is placed under immense pressure. It will literally mold itself to the shape of your rifles chamber. The first step we must take is to re-shape it to SAAMI spec, or the specifications a.223 should have.

Our resizing die will resize the brass to the SAAMI spec, and will pop the used primer out of the bottom of the case at the same time. This process needs case lubricant, the hand press, and the resizing die. We now have to chamfer the case mouth, remove the primer crimp (Ammo such as M193 and m885 have primers that are crimped in place and this crimp must be removed before you try to re-prime) and clean the primer pocket. Step 3: Priming the Case After the case prep, wash your brass again to remove the brass shavings and the case lube. Again hot, soapy water will do the trick.

Let the cases dry and then we are ready to prime the case. Here we simply put a brand new primer in the empty primer pocket. I use a hand priming tool for this in order to keep everything in the shoebox. We are ready to hand prime. The primers are placed in the hopper, and each case is fed into the rim holder and the primer is squeezed into place. Point the casing away from your face while you do this.

Step 4: Powder It goes without saying that you will have a bad day if you blow yourself up. Please read a reloading manual to understand the important concepts of reloading these concepts are things we will not fully cover here. For each loading you wish to try, you must work up a load using a ladder method and shoot these loads and observe for over-pressure signs. All of this requires careful study before you proceed.

I have already worked up a loading and will not be illustrating the incremental workup and instead I am loading to a finished product. Put the casing up to the drop chute, pull the lever up and down, and your case is filled. The powder measure must be calibrated to throw the weight you want, so read the instructions included for the proper method to do this. This relies on you following the included instructions, weighing the throw, and re weighing until a consistent loading is achieved with each throw. Step 5: Seating the Bullet The bullet seating die is a part of your press that pushes the bullet into the case mouth after you have placed your powder charge in the case.

The purpose of the die is to allow you to set the depth of the bullet and push it into the case to the desired depth / overall length. It is best to read the instructions included with the seating die and carefully adjust the seating die incrementally until the bullet is seated to the proper depth. And out pops a freshly loaded cartridge. Step 6: Optional Crimp This last step is optional. The Lee die set comes with a crimping tool. Much like the bullet seating die, it is placed in the press and the projectile is fed into the press. The crimp die then crimps the bullet which makes the bullet less likely to get set back into the case when fired in an auto-loading rifle.

Many reloaders skip this step as case neck tension should be enough to prevent this. I crimp everything.

Refer to the manual for proper setup of the crimp die. I use a very light crimp on my ammo. What About Case Cleaning and Tumbling? Some people about now are asking “when do we tumble?” I omitted tumbling as it is not necessary so long as you have CLEAN BRASS. The tarnish present on brass has not affected reliable feeding or extraction for me in thousands of rounds.

You will find that many others have come to the same conclusion: tumbling is a nice extra step, but not necessary. If you are tight on space, forgo the tumbler and give the brass a good bath. Keep in mind that if you do choose to tumble, it should be done outside. Tumblers have been shows to elevate lead and other toxic chemical levels in the air via dust production and they should be placed away from your living space.

Wrapping Up: This is a quick visual guide as to how.I. reload my shells. This is a primer which illustrates the steps I take to get a shootable product. It is important to understand all the concepts we touched upon by studying your reloading manual in-depth. This is a taste of what I do in order to reload, and I hope it can shed enough light on the process so you can make a decision as to whether you have the patience and attention to detail necessary to safely reload cartridges. Reloading is a great use of your time when you cannot hit the range, and I hope I have illustrated to you that it CAN be done in an apartment or small space.

Again if you wish to start reloading, read a quality reloading manual, understand the essential concepts, and follow the instructions. Having a few extra thousand rounds of ammo that you made yourself is a great source of pride and fills you with a warm glow. Plus Varget smells nice.