2015 Mercury 2 Stroke 115hp Outboard Manual
. IMPORTANT INFORMATION OUTBOARD MOTOR INSTALLATION. Table of Contents Page Notice to Installer and Owner. 1D-1 Boat Horsepower Capacity.1D-1 Outboard Remote Control. Boat Horsepower Capacity Mercury Marine Quicksilver accessories are avail- able from Mercury Marine dealers. Some accessories not manufactured or sold by Mer- U.S.
COAST GUARD CAPACITY cury Marine are not designed to be safely used with MAXIMUM HORSEPOWER XXX your outboard or outboard operating system. Selecting Steering Cables Lifting Outboard and Remote Control Cables WARNING Refer to “ Quicksilver Accessories Guide” to deter- Verify that the lifting ring is threaded into the fly- mine correct length of steering cables and remote wheel a minimum of 5 turns and that hoist has a control cables. Installing Outboard to Boat Use a 17/32 inch (13.5mm) diameter drill bit and drill two mounting holes for the upper set of mounting Transom bolts and two holes for the lower set of mounting bolts. NOTE: using “ Transom Drilling Fixture”. Measure the transom height of your boat.
The boat WARNING bottom should be aligned or be within 1 in. (25mm) below the anti-ventilation plate of the outboard.
Before operation, the outboard must be correctly installed with four mounting bolts shown. Failure to correctly fasten outboard could result in out- board ejecting off boat transom causing serious injury, death, or property damage. Single Steering Cable and FASTENING OUTBOARD TO THE BOAT TRANSOM Steering Link Rod Type 1 Bracket Installation Drill two 1/2 in. (12.5mm) holes thru a lower set of mounting holes and fasten outboard to boat transom NOTE: These instructions are for single cable-single with two 1/2 in. Place a mark on the tilt tube, 1/4 in. (6.4mm) from 1. Assemble steering link rod to steering cable with end of tilt tube.
Install plastic spacer, o-ring and two flat washers and nylon insert locknut cap onto steering cable as shown. Required Side Mount Remote Control or Ignition Key Switch Assembly Boats Equipped with Side Mount Remote Control A Quicksilver Commander 2000 series Side Mount Remote Control equipped with a warning horn must be used with this outboard. This warning horn is nec- essary for the engine warning system. Shift and Throttle Cable 3. Push-in on the cable end until resistance is felt.
Adjust the cable barrel to attain the measured Installation To The Outboard distance “ a”taken in Step 2. Place cable barrel into the bottom hole in the bar- Install cables into the remote control following the rel holder. Throttle Cable Installation 4. Check throttle cable adjustment as follows: a. Shift outboard into gear a few times to acti- 1. Position remote control into neutral. Vate the throttle linkage.
Mercury 2 Stroke Oil
Make sure to rotate the propeller shaft while shifting into reverse. Battery Connections Set Up Instructions For Oil Injection System CAUTION For dual outboard installations, the BLACK (- -) CAUTION battery cable of each engines starter motor Oil injected engines additionally, must be run on ground circuit, MUST BE connected to each oth- a 50:1 gasoline/oil mixture in the fuel tank for the er by a common circuit (cable) capable of carry- first 10 gallons of fuel. Bleeding Air From The Oil Injection Adjusting The Oil Injection Pump System When carburetor linkage is at idle position, alignment mark on oil injection arm should be in-line with mark IMPORTANT: If air exists in either the oil pump in- on pump as shown.
2017 triumph street scrambler manual. Tilt Pin Adjustment 4. Install thrust washer, propeller, propeller nut re- tainer, and propeller nut onto the shaft. WARNING DO NOT operate boat without the tilt pin in- stalled. Failure to install tilt pin could result in outboard kicking up when operated in reverse causing serious injury, death, or property dam- age. PLACING TILT PIN IN UPPER HOLES CAN: MODELS WITHOUT POWER TRIM 1.
Lift the bow out of the water. Operate your boat at normal cruising speed trimmed to desired position by installing the “ tilt pin”in the de- 2. Generally increase top speed. Sired tilt pin hole.
Get massive displacement and power from the lightest, easiest-to-maintain 150hp FourStroke on the market. Great for bass, aluminum console, runabout open bow, and offshore fishing boats and pontoons. The lightest low-emissions outboard in its power range. Great for deck, inshore fishing, bass, aluminum tiller, runabout open bow, inflatable rigid hull, and fish & ski boats.
Made to provide outstanding acceleration and throttle response. Great for deck, inshore fishing, bass, aluminum tiller, aluminum console, runabout open bow, inflatable rigid hull, and fish & ski boats. Enjoy the same lifetime maintenance-free valvetrain design found in our 150 FourStroke motors.
Mercury 2 Stroke Outboards
Mercury 2 Stroke 115 Outboard Leaking Oil
Great for deck, inshore fishing, bass, aluminum console, runabout open bow, inflatable rigid hull, and fish & ski boats.
Comments are closed.